--- /dev/null
+On 1/10/2004, Dan Dennedy ran the dv1394d/docs/testing.txt against
+mlt albino and miracle.
+
+Not Implemented/Completely Broken
+------------------------------------------------------------------------------
+NLS
+UADD {offline unit} -- to be supported?
+
+
+
+Incorrect Behaviour
+(Intent may be unknown in some cases.)
+------------------------------------------------------------------------------
+LOAD commences play
+STOP does not play the test card (white silence) (=pause)
+USTA when stopped reports "paused"
+REW when stopped does not rewind to the beginning of the clip.
+
+
+Different Intentional Behaviour
+------------------------------------------------------------------------------
+STOP does not terminate audio/video output
+
--- /dev/null
+
+MLT Miracle Test Procedure
+
+Copyright (C) 2003 Ushodaya Enterprised Limited
+Author: Dan Dennedy <dan@dennedy.org>
+Last Revision: 2003-01-17
+
+NOTE: THIS DOCUMENT REQUIRES REVISION TO NEW, EXPECTED BEHAVIOR FROM MIRACLE.
+
+Tests are divided into 9 sections:
+
+ 1. Command Line Usage
+ 2. Unit Management
+ 3. Server Configuration
+ 4. Simple Playback
+ 5. Multi-unit Playback
+ 6. Unit Configuration
+ 7. Advanced Playback
+ 8. Bus Reset
+ 9. Server Side Queuing
+
+Each section contains many tests which I've divided into a minimum of two lines:
+
+n.m action to carry out
+--> expected result
+
+Further lines may appear to show the actual results when they deviate from what
+I expected or if there are special cases to consider.
+
+Sequential tests are indicated as:
+
+n.m.o action to carry out
+--> expected result
+
+It is suggested that you run top during the testing and note cpu hikes
+or any excessive memory usage related to an operation.
+
+
+0. Introduction
+---------------
+
+The tests following are by no means exhaustive, but they should cover typical
+use cases - creativity is encouraged with more cases being added where necessary.
+This document should also be maintained to dictate actual state, especially with
+regard to a final release. Unit test cases are encouraged, but are excluded from
+this document.
+
+It is important to carry out the full test cycle when preparing a final release.
+In this situation, please resist the temptation to bug fix a given test case and
+resume the tests from that point onward - it is better to repeat from the
+beginning (but you can of course employ common sense in this situation).
+
+Before starting the final tests, please delete/backup your current
+/etc/dv139d.conf file. This (more or less) ensures that tests are carried out
+for a virgin install.
+
+
+1. Command Line Usage
+---------------------
+
+Run these from the top level project directory
+
+1.1.0 Start dv1394d in interactive mode: src/dv1394d -test
+--> dv1394d starts interactively and reports:
+(5) Starting server on 5250.
+(5) lt-dv1394d version 0.1.0 listening on port 5250
+
+1.1.1 Stop the server by pressing Ctrl-C
+--> dv1394d returns the following and returns control to the console:
+(5) lt-dv1394d version 0.1.0 server terminated.
+
+1.2.2 Start dv1394d as a daemon: src/dv1394d
+--> control returns to the console
+
+1.2.3 Verify dv1394d is running: ps ax
+--> five dv1394d (or lt-dv1394d) processes are running
+
+1.2.4 Verify successful dv1394d startup using syslog: sudo tail /var/log/syslog
+--> dv1394d: lt-dv1394d version 0.1.0 listening on port 5250
+
+1.2.5 Verify connectivity on port 5250: telnet localhost 5250
+--> 100 VTR Ready
+
+1.2.6 Test clean disconnect: BYE
+--> Connection closed by foreign host.
+
+1.2.7 Stop the daemon: killall lt-dv1394d
+--> no errors
+
+1.2.8 Verify a clean server shutdown: sudo tail /var/log/syslog
+--> dv1394d: shutdown complete.
+
+1.3.0 Start dv1394d on a different port: src/dv1394d -port 5260
+
+1.3.1 Verify successful dv1394d startup using syslog: sudo tail /var/log/syslog
+--> dv1394d: lt-dv1394d version 0.1.0 listening on port 5260
+
+1.3.2 Verify connectivity on port 5260: telnet localhost 5260
+--> 100 VTR Ready
+
+1.3.3 Test clean disconnect: BYE
+--> Connection closed by foreign host.
+
+1.3.4 Stop the daemon: killall lt-dv1394d
+--> no errors
+
+
+2. Unit Management
+------------------
+
+Start the dv1394d server and connect to it with telnet or a protocol-
+level client. Make sure a DV device is connected and powered.
+
+2.1 List the AV/C devices on the bus: NLS
+--> 201 OK
+--> one or more lines listing devices with GUID in second column
+
+2.2 Add a device as a dv1394d unit: UADD {GUID}
+--> 201 OK
+--> U0
+
+2.3 List the units: ULS
+--> 201 OK
+--> U0 ?? {GUID} 1
+--> It is important that the last column is '1' to indicate it is online.
+
+2.4 Add an offline unit by using some bogus GUID value: UADD foo
+--> 201 OK
+--> U1
+
+2.3 List the units: ULS
+--> 201 OK
+--> U0 ?? {GUID} 1
+--> U1 00 0000000f00055c1 0
+--> It is important that the last column of the last row is '0' to
+ indicate offline.
+
+2.4 Attempt unit commands for a unit that does not exist: LOAD U6 foo
+--> 403 Unit not found
+
+2.5 Attempt unit commands without specifying a unit: PLAY
+--> 402 Argument missing
+
+2.6 Attempt unit commands for a unit that is offline: PLAY U1
+--> 403 Unit not found
+
+2.7.0 Load a clip into an offline unit: LOAD U1 test.dv
+--> 200 OK
+
+2.7.1 Verify the status of the offline unit: USTA U1
+--> 202 OK
+--> 1 offline "test.dv" 0 1000 29.97 0 65720
+--> only the first 3 columns are relevant in this test
+
+2.9 Set the property of an online unit: USET U0 points=use
+--> 200 OK
+
+2.8 Set the property of an offline unit: USET U1 points=ignore
+--> 200 OK
+
+
+3. Server Configuration
+-----------------------
+
+Start dv1394d if not already started from a previous test.
+
+3.1 Get the hard-coded default root property value: GET root
+--> 202 OK
+--> /
+
+3.2 List the files and subdirectories at the root: CLS /
+--> 201 OK
+--> "bin/"
+--> ...
+
+3.3 Change the server root to a place where clips are stored: e.g.,
+ SET root=/tmp
+--> 200 OK
+
+3.4 Get the new value of the root property value: GET root
+--> 202 OK
+--> /tmp/
+--> Notice that if you did not use a trailing slash in step 2.3, one is
+ added for you and appears in this step. This is normal and correct.
+
+3.5 List the files and subdirectories at the root: CLS /
+--> 201 OK
+--> zero or more lines listing subdirectories followed by files.
+
+3.6 Try to set a property that does not exist: SET foo=bar
+--> 405 Argument value out of range
+
+3.7 Try to set no property or value: SET
+--> 402 Argument missing
+
+3.8 Attempt a bogus command: FOO
+--> 400 Unknown command
+
+XXX 3.9 Attempt the incorrect case for a command: get root
+XXX --> 400 Unknown command
+
+3.10 Attempt case insensitivity of property key: GET Root
+--> 202 OK
+--> /tmp/
+
+
+4. Simple Playback
+-------------------
+
+Start dv1394d or restart if already started.
+Add an online unit.
+Set the server root property if desired.
+
+4.1.0 Load a clip into the unit: LOAD U0 test.dv
+--> 200 OK
+
+4.1.1 Check the unit status: USTA U0
+--> 202 OK
+--> 0 stopped "test.dv" 0 1000 29.97 0 65720
+--> Only the first 3 columns are relevant in this test.
+--> The remaining columns are only relevant to the tester.
+
+4.2.0 Play the clip: PLAY U0
+--> 200 OK
+--> Verify audio and video output
+
+4.2.1 Check the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 1739 1000 29.97 0 65720
+--> Only the first 3 columns are relevant in this test.
+--> The remaining columns are only relevant to the tester.
+
+4.3.0 Pause playback: PAUSE U0
+--> 200 OK
+--> Verify video continues, but audio is muted.
+
+4.3.1 Check the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 1739 0 29.97 0 65720
+--> The fifth column --------^ should be 0; it indicates speed.
+
+4.3.2 Stop playback: STOP U0
+--> 200 OK
+--> The analog video output stops
+
+4.3.3 Pause playback: PAUSE U0
+--> 200 OK
+--> Analog video starts again, but it is held on the same frame
+ paused in 4.3.0.
+
+4.3.4 Stop playback: STOP U0
+--> 200 OK
+--> The analog video signal ceases.
+
+4.3.5 Rewind the unit: REW U0
+--> 200 OK
+
+4.3.6 Play the unit: PLAY U0
+--> 200 OK
+--> Analog audio and video are produced from the beginning of the file.
+
+4.4 Stop the server during playback and ensure clean shutdown.
+
+
+5. Multi-unit Playback
+-----------------------
+
+Start dv1394d or restart if already started.
+Add *2* online units.
+Set the server root property if desired.
+
+5.1.0 Load a clip into one unit: LOAD U0 test.dv
+--> 200 OK
+
+5.1.1 Load a clip into the other unit: LOAD U1 test.dv
+--> 200 OK
+
+5.1.2 Start playing one unit: PLAY U0
+--> 200 OK
+--> Verify audio and video output
+
+5.1.3 Start playing the other unit: PLAY U1
+--> 200 OK
+--> Verify audio and video output of both units
+
+5.2 Verify independence of units by pausing one of them: PAUSE U0
+--> 200 OK
+--> Verify video continues, but audio is muted on the first unit only.
+
+5.3 Stop the server during multi-unit playback and ensure clean shutdown.
+
+
+6. Advanced Playback
+--------------------
+
+Start dv1394d or restart if already started.
+Add *2* online units.
+Set the server root property if desired.
+
+Trick play modes:
+
+6.1.0 Load a clip: LOAD U0 test.dv
+--> 200 OK
+
+6.1.1 Start playback by pausing on the first frame: PAUSE U0
+--> 200 OK
+--> analog video starts, but audio is muted.
+
+6.1.2 Play fast forward: FF U0 test.dv
+--> 200 OK
+--> verify video is playing fast in the forward direction.
+
+6.1.3 Get unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 219 2000 29.97 0 65720
+--> The important column is --^, indicates speed
+
+6.1.4 Play fast reverse: REW U0 test.dv
+--> 200 OK
+--> verify analog video output is fast in the reverse direction.
+
+6.1.5 Get unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 4621 -2000 29.97 0 65720
+--> The important column is ---^, negative mean reverse
+
+6.1.6 Play slow forward: PLAY U0 500
+--> 200 OK
+--> Verify the analog video output is slow in the forward direction.
+
+6.1.7 Play reverse normal speed: PLAY U0 -1000
+--> 200 OK
+--> Verify the analog video output is at a normal speed in the reverse direction.
+--> Audio output is reverse, but not the field order of video
+
+Loading while playing:
+
+6.2.0 Stop the unit (might be playing): STOP U0
+--> 200 OK
+
+6.2.1 Rewing the unit: REW U0
+--> 200 OK
+
+6.2.2 Start playing: PLAY U0
+--> 200 OK
+--> verify analog audio and video output
+
+6.2.3 Load another clip: LOAD test002.dv
+--> 200 OK
+--> playback seamlessly switches to the new clip
+--> verify the analog appearance of the video makes a clean switch
+
+6.2.4 Load another clip, this time with in and out points:
+ LOAD test.dv 100 500 (whatever works for your test footage)
+--> 200 OK
+--> verify the analog appearance of the video makes a clean switch
+
+6.2.5 Get unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 403 1000 29.97 100 500
+--> verify position -----^ is beyond --^ in point, last column is the out
+ point specified in the previous step.
+
+Edit points:
+
+6.3.0 Load a clip: LOAD U0 test.dv
+--> 200 OK
+
+6.3.1 Pause the playback unit: PAUSE U0
+--> 200 OK
+
+6.3.2 Set the in point: SIN U0 100
+--> 200 OK
+--> verify the frame displayed in analog video out changes
+
+6.3.4 Get the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 100 0 29.97 100 65720
+--> verify position -----^ and in ---^
+
+6.3.5 Change the mode of the unit to not restrict playback to the edit
+ region: USET U0 points=ignore
+--> 200 OK
+
+6.3.6 Jump to a frame before the in frame: GOTO U0 50
+--> 200 OK
+
+6.3.7 Get the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 50 0 29.97 100 65720
+--> position -----------^ preceeds -^ (in)
+
+6.3.8 Set the unit mode to restrict playback to the edit region: USET U0 points=use
+--> 200 OK
+--> verify frame on analog video output changes
+
+6.3.9 Get the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 100 0 29.97 100 65720
+--> verify position -----^ and in ---^
+
+6.3.10 Clear the in point: SIN U0 -1
+--> 200 OK
+
+6.3.11 Get the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 100 0 29.97 0 65720
+--> verify the in point is reset ---^
+
+The above sequence should be repeated in a similar manner for the out point
+using the SOUT command.
+
+Transfer:
+
+6.4.0 Load a clip into the first unit: LOAD U0 test.dv
+--> 200 OK
+
+6.4.1 Load a clip into the second unit: LOAD U1 test002.dv
+--> 200 OK
+
+6.4.2 Start playing the first unit: PLAY U0
+--> 200 OK
+--> verify audio and video analog output
+
+6.4.3 Set an in point on the clip in the second unit: SIN U1 100
+--> 200 OK
+
+6.4.4 Play the second unit: PLAY U1
+--> 200 OK
+--> note the beginning footage
+
+6.4.5 Transfer the clip from the second to the first unit: XFER U1 U0
+--> 200 OK
+--> verify a clean switch on the analog audio and video output of the first unit.
+--> upon transfer it should play the same footage previewed in step 6.4.4
+
+6.4.5 Get the first unit's status: USTA U0
+--> 202 OK
+--> 0 playing "test002.dv" 963 1000 29.97 100 2502
+--> note the in point set from U1 ---------^
+
+
+7. Unit Configuration
+---------------------
+
+Start dv1394d or restart if already started.
+Add an online unit.
+Set the server root property if desired.
+
+7.1.0 Load a short clip: LOAD U0 test.dv
+--> 200 OK
+
+7.1.1 Play a clip: PLAY U0
+--> 200 OK
+--> Wait until it gets to the end, and it should pause on the last frame.
+
+7.1.2 Make the clip start looping: USET U0 eof=loop
+--> 200 OK
+--> verify the clip starts playing from the beginning and loops
+
+7.2.0 Set the in point: SIN U0 10
+--> 200 OK
+--> playback pauses at in point (verify with USTA U0)
+
+7.2.1 Set the out point: SOUT U0 200
+--> 200 OK
+--> playback pauses at in point (verify with USTA U0)
+
+7.2.2 Start playing again: PLAY U0
+--> 200 OK
+--> verify playback loops between in and out points
+
+7.3 Tell the unit to ignore the edit points: USET U0 points=ignore
+--> 200 OK
+--> verify playback loops over entire video file
+
+7.4 Get the current value of the points property: UGET U0 points
+--> 202 OK
+--> ignore
+
+
+8. Bus Reset
+------------
+
+Stop dv1394d if it is already running/.
+Connect two DV devices.
+Run these from the top level project directory.
+
+8.1.0 Start dv1394d in interactive mode: src/dv1394d -test
+--> dv1394d starts interactively and reports:
+--> (5) Starting server on 5250.
+--> (5) lt-dv1394d version 0.1.0 listening on port 5250
+--> Watch the activity in this console during these tests.
+
+8.1.1 Connect: telnet localhost 5250
+--> 100 VTR Ready
+
+8.1.2 List the AV/C devices on the bus: NLS
+--> 201 OK
+--> one or more lines listing devices with GUID in second column
+
+8.1.3 Add a device as a dv1394d unit: UADD {GUID}
+--> 201 OK
+--> U0
+
+8.1.3 Add another device as a dv1394d unit: UADD {GUID}
+--> 201 OK
+--> U1
+
+8.1.4 Get a status list of units: ULS
+--> 201 OK
+--> U0 01 0007360000000001 1
+--> U1 03 0003f3001100065a 1
+--> Both units are online.
+
+8.1.5 Disconnect a device
+--> see messasges from dv1394d
+
+8.1.6 Get a status list of units: ULS
+--> 201 OK
+--> U0 01 0007360000000001 1
+--> U1 03 0003f3001100065a 0
+--> One unit is offlne.
+
+8.1.7 Load a clip into the offline unit: LOAD /var/dv1394d/test.dv
+--> 200 OK
+
+8.1.8 Try to play the offline unit: PLAY U1
+--> 403 Unit not found
+
+8.1.9 Reconnect the device
+--> see messages from dv1394d
+
+8.1.10 Get a status list of units: ULS
+--> 201 OK
+--> U0 01 0007360000000001 1
+--> U1 03 0003f3001100065a 1
+--> Both units are online.
+
+8.1.11 Start playing: PLAY U1
+--> 200 OK
+
+8.1.12 Disconnect a device
+--> U1 stops playing
+
+8.1.13 Reconnect disconnected device
+
+8.1.14 Start playing: PLAY U1
+--> 200 OK
+
+9. Server Side Queuing
+----------------------
+
+This section is designed to test the server side queuing implementation added
+in the 0.2.2 release of dv1394d. Only one unit is used for these test cases, and
+users are encouraged to test with multiple units online. It is assumed that a
+number of dv files are available for use in the servers ROOT directory - this
+document assumes that they are named test001.dv and up.
+
+9.1.0 Start dv1394d in interactive mode and add a unit (all tests will assume U0)
+--> server started with unit 0 available
+
+9.1.1 Obtain a dv1394d shell (via telnet or other app).
+--> 100 VTR (if reported by the client)
+
+9.1.2 Load a clip with LOAD U0 test001.dv and PAUSE U0
+--> 200 OK
+
+9.1.3 List the clips with LIST U0
+--> 201 OK
+--> 1
+--> 0 "test001.dv" 0 6999 7000 7000
+--> The 1 on the second line denotes the number of times the list has been changed
+ via user commands (known as the 'generation' number).
+--> The third line and beyond reports the clip index (from 0 to n), file loaded, in point,
+ out point, real size of the file and the calculated size (out - in + 1 ).
+
+9.1.4 Check the unit status with USTA U0
+--> 202 OK
+--> 0 paused "test001.dv" 0 0 25.00 0 6999 7000 "test001.dv" 0 0 6999 7000 1 1 0
+--> The last two fields indicate the generation number and current clip resp.
+
+9.1.5 Append a clip with APND U0 test002.dv followed by LIST U0
+--> 201 OK
+--> 2
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 2 and current clip of 0
+
+9.1.6 Move clip 1 to clip 0 with MOVE U0 1 0 followed by LIST U0
+--> 201 OK
+--> 3
+--> 0 "test002.dv" 0 6999 7000 7000
+--> 1 "test001.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 3 and current clip of 1
+
+9.1.7 Move clip 0 to clip 1 with MOVE U0 0 1 followed by LIST U0
+--> 201 OK
+--> 4
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 4 and current clip of 0
+--> Note that the order in which you run 9.1.6 and 9.1.7 shouldn't matter as the
+ result will be identical
+
+9.1.8 Change the position to the next clip with GOTO U0 0 +1
+--> 200 OK
+--> Check that USTA U0 reports a generation of 4 and current clip of 1
+
+9.1.9 Remove all but the playing clip with CLEAN U0 followed by LIST U0
+--> 201 OK
+--> 5
+--> 0 "test002.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 5 and current clip of 0
+
+9.1.10 Insert test001.dv back into the list using INSERT U0 test001.dv and run LIST U0
+--> 201 OK
+--> 6
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 6 and current clip of 1
+
+9.1.11 Insert test003.dv at position 2 using INSERT U0 test001.dv 3 and run LIST U0
+--> 201 OK
+--> 7
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 0 6999 7000 7000
+--> 2 "test003.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 7 and current clip of 1
+
+9.1.12 Change the in point of the current clip using SIN U0 5000 and run LIST U0
+--> 201 OK
+--> 8
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 2000
+--> 2 "test003.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 8 and current clip of 1
+
+9.1.13 Change the out point of the following clip using SOUT U0 5000 +1 and run LIST U0
+--> 201 OK
+--> 9
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 2000
+--> 2 "test003.dv" 0 5000 7000 5001
+--> Check that USTA U0 reports a generation of 9 and current clip of 2
+
+9.1.14 Change the in point of the current clip to 1000 using SIN U0 1000 and run LIST U0
+--> 201 OK
+--> 10
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 2000
+--> 2 "test003.dv" 1000 5000 7000 4001
+--> Check that USTA U0 reports a generation of 10 and current clip of 2
+
+9.1.15 Ignore the in/out points by running USET U0 points=ignore and run LIST U0
+--> 201 OK
+--> 11
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 7000
+--> 2 "test003.dv" 1000 5000 7000 7000
+--> Check that USTA U0 reports a generation of 11 and current clip of 2
+
+9.1.16 Turn the in/out points on again by running USET U0 points=use and run LIST U0
+--> 201 OK
+--> 12
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 2000
+--> 2 "test003.dv" 1000 5000 7000 4001
+--> Check that USTA U0 reports a generation of 12 and current clip of 2
+
+9.1.17 Remove the current clip using REMOVE U0 and run LIST U0
+--> 201 OK
+--> 13
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 2000
+--> Check that USTA U0 reports a generation of 13 and current clip of 0
+
+9.1.17 Remove the next clip using REMOVE U0 +1 and run LIST U0
+--> 201 OK
+--> 14
+--> 0 "test001.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 14 and current clip of 0
--- /dev/null
+On 1/10/2004, Dan Dennedy ran the dv1394d/docs/testing.txt against
+mlt albino and miracle.
+
+Not Implemented/Completely Broken
+------------------------------------------------------------------------------
+NLS
+UADD {offline unit} -- to be supported?
+
+
+
+Incorrect Behaviour
+(Intent may be unknown in some cases.)
+------------------------------------------------------------------------------
+LOAD commences play
+STOP does not play the test card (white silence) (=pause)
+USTA when stopped reports "paused"
+REW when stopped does not rewind to the beginning of the clip.
+
+
+Different Intentional Behaviour
+------------------------------------------------------------------------------
+STOP does not terminate audio/video output
+
--- /dev/null
+
+MLT Miracle Test Procedure
+
+Copyright (C) 2003 Ushodaya Enterprised Limited
+Author: Dan Dennedy <dan@dennedy.org>
+Last Revision: 2003-01-17
+
+NOTE: THIS DOCUMENT REQUIRES REVISION TO NEW, EXPECTED BEHAVIOR FROM MIRACLE.
+
+Tests are divided into 9 sections:
+
+ 1. Command Line Usage
+ 2. Unit Management
+ 3. Server Configuration
+ 4. Simple Playback
+ 5. Multi-unit Playback
+ 6. Unit Configuration
+ 7. Advanced Playback
+ 8. Bus Reset
+ 9. Server Side Queuing
+
+Each section contains many tests which I've divided into a minimum of two lines:
+
+n.m action to carry out
+--> expected result
+
+Further lines may appear to show the actual results when they deviate from what
+I expected or if there are special cases to consider.
+
+Sequential tests are indicated as:
+
+n.m.o action to carry out
+--> expected result
+
+It is suggested that you run top during the testing and note cpu hikes
+or any excessive memory usage related to an operation.
+
+
+0. Introduction
+---------------
+
+The tests following are by no means exhaustive, but they should cover typical
+use cases - creativity is encouraged with more cases being added where necessary.
+This document should also be maintained to dictate actual state, especially with
+regard to a final release. Unit test cases are encouraged, but are excluded from
+this document.
+
+It is important to carry out the full test cycle when preparing a final release.
+In this situation, please resist the temptation to bug fix a given test case and
+resume the tests from that point onward - it is better to repeat from the
+beginning (but you can of course employ common sense in this situation).
+
+Before starting the final tests, please delete/backup your current
+/etc/dv139d.conf file. This (more or less) ensures that tests are carried out
+for a virgin install.
+
+
+1. Command Line Usage
+---------------------
+
+Run these from the top level project directory
+
+1.1.0 Start dv1394d in interactive mode: src/dv1394d -test
+--> dv1394d starts interactively and reports:
+(5) Starting server on 5250.
+(5) lt-dv1394d version 0.1.0 listening on port 5250
+
+1.1.1 Stop the server by pressing Ctrl-C
+--> dv1394d returns the following and returns control to the console:
+(5) lt-dv1394d version 0.1.0 server terminated.
+
+1.2.2 Start dv1394d as a daemon: src/dv1394d
+--> control returns to the console
+
+1.2.3 Verify dv1394d is running: ps ax
+--> five dv1394d (or lt-dv1394d) processes are running
+
+1.2.4 Verify successful dv1394d startup using syslog: sudo tail /var/log/syslog
+--> dv1394d: lt-dv1394d version 0.1.0 listening on port 5250
+
+1.2.5 Verify connectivity on port 5250: telnet localhost 5250
+--> 100 VTR Ready
+
+1.2.6 Test clean disconnect: BYE
+--> Connection closed by foreign host.
+
+1.2.7 Stop the daemon: killall lt-dv1394d
+--> no errors
+
+1.2.8 Verify a clean server shutdown: sudo tail /var/log/syslog
+--> dv1394d: shutdown complete.
+
+1.3.0 Start dv1394d on a different port: src/dv1394d -port 5260
+
+1.3.1 Verify successful dv1394d startup using syslog: sudo tail /var/log/syslog
+--> dv1394d: lt-dv1394d version 0.1.0 listening on port 5260
+
+1.3.2 Verify connectivity on port 5260: telnet localhost 5260
+--> 100 VTR Ready
+
+1.3.3 Test clean disconnect: BYE
+--> Connection closed by foreign host.
+
+1.3.4 Stop the daemon: killall lt-dv1394d
+--> no errors
+
+
+2. Unit Management
+------------------
+
+Start the dv1394d server and connect to it with telnet or a protocol-
+level client. Make sure a DV device is connected and powered.
+
+2.1 List the AV/C devices on the bus: NLS
+--> 201 OK
+--> one or more lines listing devices with GUID in second column
+
+2.2 Add a device as a dv1394d unit: UADD {GUID}
+--> 201 OK
+--> U0
+
+2.3 List the units: ULS
+--> 201 OK
+--> U0 ?? {GUID} 1
+--> It is important that the last column is '1' to indicate it is online.
+
+2.4 Add an offline unit by using some bogus GUID value: UADD foo
+--> 201 OK
+--> U1
+
+2.3 List the units: ULS
+--> 201 OK
+--> U0 ?? {GUID} 1
+--> U1 00 0000000f00055c1 0
+--> It is important that the last column of the last row is '0' to
+ indicate offline.
+
+2.4 Attempt unit commands for a unit that does not exist: LOAD U6 foo
+--> 403 Unit not found
+
+2.5 Attempt unit commands without specifying a unit: PLAY
+--> 402 Argument missing
+
+2.6 Attempt unit commands for a unit that is offline: PLAY U1
+--> 403 Unit not found
+
+2.7.0 Load a clip into an offline unit: LOAD U1 test.dv
+--> 200 OK
+
+2.7.1 Verify the status of the offline unit: USTA U1
+--> 202 OK
+--> 1 offline "test.dv" 0 1000 29.97 0 65720
+--> only the first 3 columns are relevant in this test
+
+2.9 Set the property of an online unit: USET U0 points=use
+--> 200 OK
+
+2.8 Set the property of an offline unit: USET U1 points=ignore
+--> 200 OK
+
+
+3. Server Configuration
+-----------------------
+
+Start dv1394d if not already started from a previous test.
+
+3.1 Get the hard-coded default root property value: GET root
+--> 202 OK
+--> /
+
+3.2 List the files and subdirectories at the root: CLS /
+--> 201 OK
+--> "bin/"
+--> ...
+
+3.3 Change the server root to a place where clips are stored: e.g.,
+ SET root=/tmp
+--> 200 OK
+
+3.4 Get the new value of the root property value: GET root
+--> 202 OK
+--> /tmp/
+--> Notice that if you did not use a trailing slash in step 2.3, one is
+ added for you and appears in this step. This is normal and correct.
+
+3.5 List the files and subdirectories at the root: CLS /
+--> 201 OK
+--> zero or more lines listing subdirectories followed by files.
+
+3.6 Try to set a property that does not exist: SET foo=bar
+--> 405 Argument value out of range
+
+3.7 Try to set no property or value: SET
+--> 402 Argument missing
+
+3.8 Attempt a bogus command: FOO
+--> 400 Unknown command
+
+XXX 3.9 Attempt the incorrect case for a command: get root
+XXX --> 400 Unknown command
+
+3.10 Attempt case insensitivity of property key: GET Root
+--> 202 OK
+--> /tmp/
+
+
+4. Simple Playback
+-------------------
+
+Start dv1394d or restart if already started.
+Add an online unit.
+Set the server root property if desired.
+
+4.1.0 Load a clip into the unit: LOAD U0 test.dv
+--> 200 OK
+
+4.1.1 Check the unit status: USTA U0
+--> 202 OK
+--> 0 stopped "test.dv" 0 1000 29.97 0 65720
+--> Only the first 3 columns are relevant in this test.
+--> The remaining columns are only relevant to the tester.
+
+4.2.0 Play the clip: PLAY U0
+--> 200 OK
+--> Verify audio and video output
+
+4.2.1 Check the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 1739 1000 29.97 0 65720
+--> Only the first 3 columns are relevant in this test.
+--> The remaining columns are only relevant to the tester.
+
+4.3.0 Pause playback: PAUSE U0
+--> 200 OK
+--> Verify video continues, but audio is muted.
+
+4.3.1 Check the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 1739 0 29.97 0 65720
+--> The fifth column --------^ should be 0; it indicates speed.
+
+4.3.2 Stop playback: STOP U0
+--> 200 OK
+--> The analog video output stops
+
+4.3.3 Pause playback: PAUSE U0
+--> 200 OK
+--> Analog video starts again, but it is held on the same frame
+ paused in 4.3.0.
+
+4.3.4 Stop playback: STOP U0
+--> 200 OK
+--> The analog video signal ceases.
+
+4.3.5 Rewind the unit: REW U0
+--> 200 OK
+
+4.3.6 Play the unit: PLAY U0
+--> 200 OK
+--> Analog audio and video are produced from the beginning of the file.
+
+4.4 Stop the server during playback and ensure clean shutdown.
+
+
+5. Multi-unit Playback
+-----------------------
+
+Start dv1394d or restart if already started.
+Add *2* online units.
+Set the server root property if desired.
+
+5.1.0 Load a clip into one unit: LOAD U0 test.dv
+--> 200 OK
+
+5.1.1 Load a clip into the other unit: LOAD U1 test.dv
+--> 200 OK
+
+5.1.2 Start playing one unit: PLAY U0
+--> 200 OK
+--> Verify audio and video output
+
+5.1.3 Start playing the other unit: PLAY U1
+--> 200 OK
+--> Verify audio and video output of both units
+
+5.2 Verify independence of units by pausing one of them: PAUSE U0
+--> 200 OK
+--> Verify video continues, but audio is muted on the first unit only.
+
+5.3 Stop the server during multi-unit playback and ensure clean shutdown.
+
+
+6. Advanced Playback
+--------------------
+
+Start dv1394d or restart if already started.
+Add *2* online units.
+Set the server root property if desired.
+
+Trick play modes:
+
+6.1.0 Load a clip: LOAD U0 test.dv
+--> 200 OK
+
+6.1.1 Start playback by pausing on the first frame: PAUSE U0
+--> 200 OK
+--> analog video starts, but audio is muted.
+
+6.1.2 Play fast forward: FF U0 test.dv
+--> 200 OK
+--> verify video is playing fast in the forward direction.
+
+6.1.3 Get unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 219 2000 29.97 0 65720
+--> The important column is --^, indicates speed
+
+6.1.4 Play fast reverse: REW U0 test.dv
+--> 200 OK
+--> verify analog video output is fast in the reverse direction.
+
+6.1.5 Get unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 4621 -2000 29.97 0 65720
+--> The important column is ---^, negative mean reverse
+
+6.1.6 Play slow forward: PLAY U0 500
+--> 200 OK
+--> Verify the analog video output is slow in the forward direction.
+
+6.1.7 Play reverse normal speed: PLAY U0 -1000
+--> 200 OK
+--> Verify the analog video output is at a normal speed in the reverse direction.
+--> Audio output is reverse, but not the field order of video
+
+Loading while playing:
+
+6.2.0 Stop the unit (might be playing): STOP U0
+--> 200 OK
+
+6.2.1 Rewing the unit: REW U0
+--> 200 OK
+
+6.2.2 Start playing: PLAY U0
+--> 200 OK
+--> verify analog audio and video output
+
+6.2.3 Load another clip: LOAD test002.dv
+--> 200 OK
+--> playback seamlessly switches to the new clip
+--> verify the analog appearance of the video makes a clean switch
+
+6.2.4 Load another clip, this time with in and out points:
+ LOAD test.dv 100 500 (whatever works for your test footage)
+--> 200 OK
+--> verify the analog appearance of the video makes a clean switch
+
+6.2.5 Get unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 403 1000 29.97 100 500
+--> verify position -----^ is beyond --^ in point, last column is the out
+ point specified in the previous step.
+
+Edit points:
+
+6.3.0 Load a clip: LOAD U0 test.dv
+--> 200 OK
+
+6.3.1 Pause the playback unit: PAUSE U0
+--> 200 OK
+
+6.3.2 Set the in point: SIN U0 100
+--> 200 OK
+--> verify the frame displayed in analog video out changes
+
+6.3.4 Get the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 100 0 29.97 100 65720
+--> verify position -----^ and in ---^
+
+6.3.5 Change the mode of the unit to not restrict playback to the edit
+ region: USET U0 points=ignore
+--> 200 OK
+
+6.3.6 Jump to a frame before the in frame: GOTO U0 50
+--> 200 OK
+
+6.3.7 Get the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 50 0 29.97 100 65720
+--> position -----------^ preceeds -^ (in)
+
+6.3.8 Set the unit mode to restrict playback to the edit region: USET U0 points=use
+--> 200 OK
+--> verify frame on analog video output changes
+
+6.3.9 Get the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 100 0 29.97 100 65720
+--> verify position -----^ and in ---^
+
+6.3.10 Clear the in point: SIN U0 -1
+--> 200 OK
+
+6.3.11 Get the unit status: USTA U0
+--> 202 OK
+--> 0 playing "test.dv" 100 0 29.97 0 65720
+--> verify the in point is reset ---^
+
+The above sequence should be repeated in a similar manner for the out point
+using the SOUT command.
+
+Transfer:
+
+6.4.0 Load a clip into the first unit: LOAD U0 test.dv
+--> 200 OK
+
+6.4.1 Load a clip into the second unit: LOAD U1 test002.dv
+--> 200 OK
+
+6.4.2 Start playing the first unit: PLAY U0
+--> 200 OK
+--> verify audio and video analog output
+
+6.4.3 Set an in point on the clip in the second unit: SIN U1 100
+--> 200 OK
+
+6.4.4 Play the second unit: PLAY U1
+--> 200 OK
+--> note the beginning footage
+
+6.4.5 Transfer the clip from the second to the first unit: XFER U1 U0
+--> 200 OK
+--> verify a clean switch on the analog audio and video output of the first unit.
+--> upon transfer it should play the same footage previewed in step 6.4.4
+
+6.4.5 Get the first unit's status: USTA U0
+--> 202 OK
+--> 0 playing "test002.dv" 963 1000 29.97 100 2502
+--> note the in point set from U1 ---------^
+
+
+7. Unit Configuration
+---------------------
+
+Start dv1394d or restart if already started.
+Add an online unit.
+Set the server root property if desired.
+
+7.1.0 Load a short clip: LOAD U0 test.dv
+--> 200 OK
+
+7.1.1 Play a clip: PLAY U0
+--> 200 OK
+--> Wait until it gets to the end, and it should pause on the last frame.
+
+7.1.2 Make the clip start looping: USET U0 eof=loop
+--> 200 OK
+--> verify the clip starts playing from the beginning and loops
+
+7.2.0 Set the in point: SIN U0 10
+--> 200 OK
+--> playback pauses at in point (verify with USTA U0)
+
+7.2.1 Set the out point: SOUT U0 200
+--> 200 OK
+--> playback pauses at in point (verify with USTA U0)
+
+7.2.2 Start playing again: PLAY U0
+--> 200 OK
+--> verify playback loops between in and out points
+
+7.3 Tell the unit to ignore the edit points: USET U0 points=ignore
+--> 200 OK
+--> verify playback loops over entire video file
+
+7.4 Get the current value of the points property: UGET U0 points
+--> 202 OK
+--> ignore
+
+
+8. Bus Reset
+------------
+
+Stop dv1394d if it is already running/.
+Connect two DV devices.
+Run these from the top level project directory.
+
+8.1.0 Start dv1394d in interactive mode: src/dv1394d -test
+--> dv1394d starts interactively and reports:
+--> (5) Starting server on 5250.
+--> (5) lt-dv1394d version 0.1.0 listening on port 5250
+--> Watch the activity in this console during these tests.
+
+8.1.1 Connect: telnet localhost 5250
+--> 100 VTR Ready
+
+8.1.2 List the AV/C devices on the bus: NLS
+--> 201 OK
+--> one or more lines listing devices with GUID in second column
+
+8.1.3 Add a device as a dv1394d unit: UADD {GUID}
+--> 201 OK
+--> U0
+
+8.1.3 Add another device as a dv1394d unit: UADD {GUID}
+--> 201 OK
+--> U1
+
+8.1.4 Get a status list of units: ULS
+--> 201 OK
+--> U0 01 0007360000000001 1
+--> U1 03 0003f3001100065a 1
+--> Both units are online.
+
+8.1.5 Disconnect a device
+--> see messasges from dv1394d
+
+8.1.6 Get a status list of units: ULS
+--> 201 OK
+--> U0 01 0007360000000001 1
+--> U1 03 0003f3001100065a 0
+--> One unit is offlne.
+
+8.1.7 Load a clip into the offline unit: LOAD /var/dv1394d/test.dv
+--> 200 OK
+
+8.1.8 Try to play the offline unit: PLAY U1
+--> 403 Unit not found
+
+8.1.9 Reconnect the device
+--> see messages from dv1394d
+
+8.1.10 Get a status list of units: ULS
+--> 201 OK
+--> U0 01 0007360000000001 1
+--> U1 03 0003f3001100065a 1
+--> Both units are online.
+
+8.1.11 Start playing: PLAY U1
+--> 200 OK
+
+8.1.12 Disconnect a device
+--> U1 stops playing
+
+8.1.13 Reconnect disconnected device
+
+8.1.14 Start playing: PLAY U1
+--> 200 OK
+
+9. Server Side Queuing
+----------------------
+
+This section is designed to test the server side queuing implementation added
+in the 0.2.2 release of dv1394d. Only one unit is used for these test cases, and
+users are encouraged to test with multiple units online. It is assumed that a
+number of dv files are available for use in the servers ROOT directory - this
+document assumes that they are named test001.dv and up.
+
+9.1.0 Start dv1394d in interactive mode and add a unit (all tests will assume U0)
+--> server started with unit 0 available
+
+9.1.1 Obtain a dv1394d shell (via telnet or other app).
+--> 100 VTR (if reported by the client)
+
+9.1.2 Load a clip with LOAD U0 test001.dv and PAUSE U0
+--> 200 OK
+
+9.1.3 List the clips with LIST U0
+--> 201 OK
+--> 1
+--> 0 "test001.dv" 0 6999 7000 7000
+--> The 1 on the second line denotes the number of times the list has been changed
+ via user commands (known as the 'generation' number).
+--> The third line and beyond reports the clip index (from 0 to n), file loaded, in point,
+ out point, real size of the file and the calculated size (out - in + 1 ).
+
+9.1.4 Check the unit status with USTA U0
+--> 202 OK
+--> 0 paused "test001.dv" 0 0 25.00 0 6999 7000 "test001.dv" 0 0 6999 7000 1 1 0
+--> The last two fields indicate the generation number and current clip resp.
+
+9.1.5 Append a clip with APND U0 test002.dv followed by LIST U0
+--> 201 OK
+--> 2
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 2 and current clip of 0
+
+9.1.6 Move clip 1 to clip 0 with MOVE U0 1 0 followed by LIST U0
+--> 201 OK
+--> 3
+--> 0 "test002.dv" 0 6999 7000 7000
+--> 1 "test001.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 3 and current clip of 1
+
+9.1.7 Move clip 0 to clip 1 with MOVE U0 0 1 followed by LIST U0
+--> 201 OK
+--> 4
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 4 and current clip of 0
+--> Note that the order in which you run 9.1.6 and 9.1.7 shouldn't matter as the
+ result will be identical
+
+9.1.8 Change the position to the next clip with GOTO U0 0 +1
+--> 200 OK
+--> Check that USTA U0 reports a generation of 4 and current clip of 1
+
+9.1.9 Remove all but the playing clip with CLEAN U0 followed by LIST U0
+--> 201 OK
+--> 5
+--> 0 "test002.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 5 and current clip of 0
+
+9.1.10 Insert test001.dv back into the list using INSERT U0 test001.dv and run LIST U0
+--> 201 OK
+--> 6
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 6 and current clip of 1
+
+9.1.11 Insert test003.dv at position 2 using INSERT U0 test001.dv 3 and run LIST U0
+--> 201 OK
+--> 7
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 0 6999 7000 7000
+--> 2 "test003.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 7 and current clip of 1
+
+9.1.12 Change the in point of the current clip using SIN U0 5000 and run LIST U0
+--> 201 OK
+--> 8
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 2000
+--> 2 "test003.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 8 and current clip of 1
+
+9.1.13 Change the out point of the following clip using SOUT U0 5000 +1 and run LIST U0
+--> 201 OK
+--> 9
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 2000
+--> 2 "test003.dv" 0 5000 7000 5001
+--> Check that USTA U0 reports a generation of 9 and current clip of 2
+
+9.1.14 Change the in point of the current clip to 1000 using SIN U0 1000 and run LIST U0
+--> 201 OK
+--> 10
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 2000
+--> 2 "test003.dv" 1000 5000 7000 4001
+--> Check that USTA U0 reports a generation of 10 and current clip of 2
+
+9.1.15 Ignore the in/out points by running USET U0 points=ignore and run LIST U0
+--> 201 OK
+--> 11
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 7000
+--> 2 "test003.dv" 1000 5000 7000 7000
+--> Check that USTA U0 reports a generation of 11 and current clip of 2
+
+9.1.16 Turn the in/out points on again by running USET U0 points=use and run LIST U0
+--> 201 OK
+--> 12
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 2000
+--> 2 "test003.dv" 1000 5000 7000 4001
+--> Check that USTA U0 reports a generation of 12 and current clip of 2
+
+9.1.17 Remove the current clip using REMOVE U0 and run LIST U0
+--> 201 OK
+--> 13
+--> 0 "test001.dv" 0 6999 7000 7000
+--> 1 "test002.dv" 5000 6999 7000 2000
+--> Check that USTA U0 reports a generation of 13 and current clip of 0
+
+9.1.17 Remove the next clip using REMOVE U0 +1 and run LIST U0
+--> 201 OK
+--> 14
+--> 0 "test001.dv" 0 6999 7000 7000
+--> Check that USTA U0 reports a generation of 14 and current clip of 0
projects / melted / commitdiff